Date: 27.02.2003
Component: Air Bags > Frontal > Driver Side Inflator Module
Manufacturer: Nissan North America, Inc.
Description:
On certain vehicles, the electrical connector for the driver air bag may come loose. if the connector comes loose, the supplemental air bag warning light flashes intermittently.
Consequencs:
The driver side air bag will not deploy in the event of a crash, increasing the risk of personal injury.
Notes:
Dealers will install a retaining clip on the clock spring electrical connector. owner notification began april 21, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact nissan at 1-800-647-7261.
Date: 17.04.2002
Component: Air Bags
Manufacturer: Nissan North America, Inc.
Description:
This is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. on certain 2002 nissan altima model vehicles manufactured prior to march 16, 2002, one of the sensors for the air bag system does not work as well as expected in high-speed off-set crash situations.
Consequencs:
The air bag system does not work as expected.
Notes:
Dealers will replace the air bag sensor. owner notification began april 15, 2002. owners should contact nissan at 1-800-647-7261, concerning the problem.
Date: 17.11.2003
Component: Engine And Engine Cooling
Manufacturer: Nissan North America, Inc.
Description:
On certain passenger vehicles, the circuit board for the crank position sensor or cam position sensor may have an improper solder joint due to solder deformation caused by heat stress accelerated by the existence of flux residue during the soldering process.
Consequencs:
This could cause the "service engine soon" warning light to come on, create a no start condition, cause reduced engine power, or cause the engine to stop running without warning during vehicle operation, which could result in a crash.
Notes:
Dealers will replace the crank position sensors. camshaft position sensor(s), and in some cases, the variable timing control sensor(s). vehicles involved in a previous recall campaign, 01v357, are also included in this new campaign. the replacement sensors used in that campaign are also affected. owner notification began on december 22, 2003. owners should contact nissan at 1-800-647-7261 or infiniti at 1-800-662-6200.
Date: 17.11.2003
Component: Engine And Engine Cooling
Manufacturer: Nissan North America, Inc.
Description:
On certain passenger vehicles, the circuit board for the crank position sensor or cam position sensor may have an improper solder joint due to solder deformation caused by heat stress accelerated by the existence of flux residue during the soldering process.
Consequencs:
This could cause the "service engine soon" warning light to come on, create a no start condition, cause reduced engine power, or cause the engine to stop running without warning during vehicle operation, which could result in a crash.
Notes:
Dealers will replace the crank position sensors. camshaft position sensor(s), and in some cases, the variable timing control sensor(s). vehicles involved in a previous recall campaign, 01v357, are also included in this new campaign. the replacement sensors used in that campaign are also affected. owner notification began on december 22, 2003. owners should contact nissan at 1-800-647-7261 or infiniti at 1-800-662-6200.
Date: 14.11.2007
Component: Engine And Engine Cooling
Manufacturer: Nissan North America, Inc.
Description:
On certain passenger vehicles equipped with a 2.5l engine, the crankshaft position sensor can overheat causing a brief interruption in the signal output from the sensor.
Consequencs:
If the interruption in the signal from the crankshaft position sensor is so brief that the electronic control module (ecm) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at a low speed increasing the risk of a crash.
Notes:
Dealers will reprogram the ecm free of charge. certain my 2006 altimas which have been previously remedied under recall campaign 06v223 (nissan r0606) are not included in this recall since the reprogramming for 06v223 also included this reprogramming. the recall began on december 31, 2007. owners may contact nissan at 1-800-647-7261.
Date: 14.07.2003
Component: Fuel System, Gasoline > Storage > Tank Assembly
Manufacturer: Nissan North America, Inc.
Description:
On certain passenger vehicles originally sold in or currently registered in the states of alaska, colorado, connecticut, iowa, idaho, illinois, indiana, kansas, massachusetts, maine, michigan, minnesota, missouri, montana, north dakota, nebraska, new hampshire, new york, ohio, pennsylvania, rhode island, south dakota, utah, vermont, wisconsin, and wyoming. at extremely cold temperatures, moisture in the fuel tank could freeze and form ice crystals. these ice crystals may obstruct the suction opening of the fuel pump.
Consequencs:
This can prevent the supply of fuel to the engine and cause the engine to stop, which could result in a crash without warning.
Notes:
Dealers will install a screen at the suction opening of the fuel pump to prevent ice crystals from blocking the opening. owner notification began on august 18, 2003. owners should contact nissan at 1-800-333-0829.
Date: 14.07.2003
Component: Fuel System, Gasoline > Storage > Tank Assembly
Manufacturer: Nissan North America, Inc.
Description:
On certain passenger vehicles originally sold in or currently registered in the states of alaska, colorado, connecticut, iowa, idaho, illinois, indiana, kansas, massachusetts, maine, michigan, minnesota, missouri, montana, north dakota, nebraska, new hampshire, new york, ohio, pennsylvania, rhode island, south dakota, utah, vermont, wisconsin, and wyoming. at extremely cold temperatures, moisture in the fuel tank could freeze and form ice crystals. these ice crystals may obstruct the suction opening of the fuel pump.
Consequencs:
This can prevent the supply of fuel to the engine and cause the engine to stop, which could result in a crash without warning.
Notes:
Dealers will install a screen at the suction opening of the fuel pump to prevent ice crystals from blocking the opening. owner notification began on august 18, 2003. owners should contact nissan at 1-800-333-0829.
Date: 11.03.2003
Component: Engine And Engine Cooling > Exhaust System > Manifold/header/muffler/tail Pipe
Manufacturer: Nissan North America, Inc.
Description:
On certain vehicles equipped with the 2.5 liter engine, the exhaust pipe hanger pin may catch debris from the road that could be ignited by contact with the main catalyst. also on 2002 altima and sentra vehicles, certain engine operating conditions may cause the pre-catalyst to overheat and damage the catalyst substrate.
Consequencs:
Either of these two conditions could result in a fire.
Notes:
Dealers will remove the protruding portion of the exhaust pipe hanger pin. in addition to the corrective action, in order to reduce the risk of fire in the event of poor or improper maintenance that could result in oil spillage, heat shield(s) will be installed on the pre-catalyst and exhaust tube. owner notification began on july 28, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact nissan at 1-800-647-7261. nissan recall nos. r3007, r3014, r3015, r3016, r3017. also on 2002 altima and sentra vehicles, certain engine operating conditions may cause the pre-catalyst to overheat and damage the catalyst substrate. if substrate particles enter the combustion chamber, they could score the cylinder walls, resulting in increased oil consumption. if the engine oil level is not checked on a periodic basis and drops below the low level, and the driver continues to operate the vehicle ignoring noticeable engine noise, engine damage may occur which could result in a fire. the pre-catalyst will be tested to ensure it is working properly and replaced if necessary. if damage is found inside the pre-catalyst, it will be necessary to replace the engine.
Date: 11.03.2003
Component: Engine And Engine Cooling > Exhaust System > Manifold/header/muffler/tail Pipe
Manufacturer: Nissan North America, Inc.
Description:
On certain vehicles equipped with the 2.5 liter engine, the exhaust pipe hanger pin may catch debris from the road that could be ignited by contact with the main catalyst. also on 2002 altima and sentra vehicles, certain engine operating conditions may cause the pre-catalyst to overheat and damage the catalyst substrate.
Consequencs:
Either of these two conditions could result in a fire.
Notes:
Dealers will remove the protruding portion of the exhaust pipe hanger pin. in addition to the corrective action, in order to reduce the risk of fire in the event of poor or improper maintenance that could result in oil spillage, heat shield(s) will be installed on the pre-catalyst and exhaust tube. owner notification began on july 28, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact nissan at 1-800-647-7261. nissan recall nos. r3007, r3014, r3015, r3016, r3017. also on 2002 altima and sentra vehicles, certain engine operating conditions may cause the pre-catalyst to overheat and damage the catalyst substrate. if substrate particles enter the combustion chamber, they could score the cylinder walls, resulting in increased oil consumption. if the engine oil level is not checked on a periodic basis and drops below the low level, and the driver continues to operate the vehicle ignoring noticeable engine noise, engine damage may occur which could result in a fire. the pre-catalyst will be tested to ensure it is working properly and replaced if necessary. if damage is found inside the pre-catalyst, it will be necessary to replace the engine.
